3.1.0.BETA3

* Version Bump to 3.1.0.BETA3
 * Bugfixes
 * adresse issue: #39

Arduino/McLighting/McLighting.ino

@@ -535,11 +535,11 @@ void setup() {
   DBG_OUTPUT_PORT.print("Use http://");
   DBG_OUTPUT_PORT.print(HOSTNAME);
   DBG_OUTPUT_PORT.println(".local/ when you have Bonjour installed.");
-
+#if !defined(USE_HTML_MIN_GZ)
   DBG_OUTPUT_PORT.print("New users: Open http://");
   DBG_OUTPUT_PORT.print(WiFi.localIP());
   DBG_OUTPUT_PORT.println("/upload to upload the webpages first.");
-
+#endif
   DBG_OUTPUT_PORT.println("");
 
   // ***************************************************************************

Arduino/McLighting/definitions.h

@@ -12,7 +12,6 @@
 #define FX_OPTIONS 48      // ws2812fx Options 48 = SIZE_SMALL + FADE_MEDIUM  is configurable just for the start; for WS2812FX setSegment OPTIONS, see: https://github.com/kitesurfer1404/WS2812FX/blob/master/extras/WS2812FX%20Users%20Guide.md
 //#define LED_TYPE_WS2811    // Uncomment, if LED type uses 400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
 #define LED_BUILTIN 2      // ESP-12F has the built in LED on GPIO2, see https://github.com/esp8266/Arduino/issues/2192 
-//#define POWER_SUPPLY 12    // PIN (12 / D6) If defined, enable output to control external power supply 
 char HOSTNAME[65] = "McLightingRGBW"; // Friedly hostname  is configurable just for the start. Hostname should not contain spaces as this can break Home Assistant discovery if used.
 
 #define ENABLE_OTA 1                  // If defined, enable Arduino OTA code. If set to 0 enable Arduino OTA code, if set to 1 enable ESP8266HTTPUpdateServer OTA code.
@@ -21,12 +20,15 @@ char HOSTNAME[65] = "McLightingRGBW"; // Friedly hostname  is configurable just
 //#define ENABLE_MQTT_INCLUDE_IP        // uncomment/comment to add the IP-adress to the MQTT message
 #define ENABLE_HOMEASSISTANT          // If defined, enable Homeassistant integration, ENABLE_MQTT must be active
 #define MQTT_HOME_ASSISTANT_SUPPORT   // If defined, use AMQTT and select Tools -> IwIP Variant -> Higher Bandwidth
+
 #define ENABLE_BUTTON 14              // If defined, enable button handling code, see: https://github.com/toblum/McLighting/wiki/Button-control, the value defines the input pin (14 / D5) for switching the LED strip on / off, connect this PIN to ground to trigger button.
 //#define ENABLE_BUTTON_GY33 12         // If defined, enable button handling code for GY-33 color sensor to scan color. The value defines the input pin (12 / D6) for read color data with RGB sensor, connect this PIN to ground to trigger button.
+//#define POWER_SUPPLY 12               // PIN (12 / D6) If defined, enable output to control external power supply
+//#define ENABLE_REMOTE 13              // If defined, enable Remote Control via TSOP31238. The value defines the input pin (13 / D7) for TSOP31238 Out 
+
 #if defined(ENABLE_BUTTON_GY33)
   #define GAMMA 2.5                   // Gamma correction for GY-33 sensor
 #endif
-//#define ENABLE_REMOTE 13              // If defined, enable Remote Control via TSOP31238. The value defines the input pin (13 / D7) for TSOP31238 Out 
 
 #define ENABLE_STATE_SAVE             // If defined, load saved state on reboot and save state on SPIFFS 
 

Arduino/McLighting/request_handlers.h

@@ -712,8 +712,9 @@ void webSocketEvent(uint8_t num, WStype_t type, uint8_t * payload, size_t lenght
        JsonObject root = jsonBuffer.to<JsonObject>();
        root["state"] = (State.mode != OFF) ? on_cmd : off_cmd;
        #if defined(ENABLE_MQTT_INCLUDE_IP) 
-         root["ip"] = WiFi.localIP();
+         root["ip"] = WiFi.localIP().toString();
        #endif
+       root["segment"] = State.segment;
        JsonObject color = root.createNestedObject("color");
        color["r"] = main_color.red;
        color["g"] = main_color.green;

Arduino/McLighting/version.h

@@ -1 +1 @@
-#define SKETCH_VERSION "3.1.0.BETA2"
+#define SKETCH_VERSION "3.1.0.BETA3"

Arduino/McLighting/version_info.ino

@@ -216,4 +216,10 @@
  * Version Bump to 3.1.0.BETA2
  * bugfixes
  * implemented https://github.com/FabLab-Luenen/McLighting/commit/589806d0fda737011426754a6d84c88535ded688
+ * 
+ * 20 October
+ * Version Bump to 3.1.0.BETA3
+ * Bugfixes
+ * adresse issue: #39
+ * 
  */