Version Bump to 3.1.1

* bugfixes regarding issue #80

Arduino/McLighting/McLighting.ino

@@ -747,7 +747,7 @@ void loop() {
       #endif
       #if defined(ENABLE_HOMEASSISTANT)
         if(ha_send_data.active()) ha_send_data.detach();
-        ha_send_data.once(5, tickerSendState);
+        ha_send_data.once(DELAY_MQTT_HA_MESSAGE, tickerSendState);
       #endif
     #endif
   }

Arduino/McLighting/definitions.h

@@ -20,7 +20,7 @@ char HOSTNAME[65] = "McLightingRGBW"; // Friedly hostname  is configurable just
 //#define ENABLE_MQTT_INCLUDE_IP        // uncomment/comment to add the IP-adress to the MQTT message
 #define ENABLE_HOMEASSISTANT          // If defined, enable Homeassistant integration, ENABLE_MQTT must be active
 #define MQTT_HOME_ASSISTANT_SUPPORT   // If defined, use AMQTT and select Tools -> IwIP Variant -> Higher Bandwidth
-//#define DISABLE_MQTT_OUT_ON_MQTT_IN   // If defined, McLighting will not send back MQTT-out on MQTT-in regarding issue #67, does not change anything at the moment
+#define DELAY_MQTT_HA_MESSAGE 5       // HA Status is send after DELAY_MQTT_HA_MESSAGE seconds, to save bandwith
 
 //#define ENABLE_BUTTON 14              // If defined, enable button handling code, see: https://github.com/toblum/McLighting/wiki/Button-control, the value defines the input pin (14 / D5) for switching the LED strip on / off, connect this PIN to ground to trigger button.
 //#define ENABLE_BUTTON_GY33 12         // If defined, enable button handling code for GY-33 color sensor to scan color. The value defines the input pin (12 / D6) for read color data with RGB sensor, connect this PIN to ground to trigger button.
@@ -28,7 +28,7 @@ char HOSTNAME[65] = "McLightingRGBW"; // Friedly hostname  is configurable just
 #if defined(POWER_SUPPLY)
   #define POWER_ON   HIGH           // Define the output state to turn on the power supply, either HIGH or LOW.  Opposite will be uses for power off.
 #endif
-#define ENABLE_REMOTE 13              // If defined, enable Remote Control via TSOP31238. The value defines the input pin (13 / D7) for TSOP31238 Out
+//#define ENABLE_REMOTE 13              // If defined, enable Remote Control via TSOP31238. The value defines the input pin (13 / D7) for TSOP31238 Out
 
 #if defined(ENABLE_BUTTON_GY33)
   #define GAMMA 2.5                   // Gamma correction for GY-33 sensor
@@ -178,10 +178,10 @@ struct {
       uint8_t pin = 3;
     #endif
     #if USE_WS2812FX_DMA == 1
-      uint8_t pin = 2;
+      uint8_t pin = 1;
     #endif
     #if USE_WS2812FX_DMA == 2
-      uint8_t pin = 1;
+      uint8_t pin = 2;
     #endif
   #else
     uint8_t pin = LED_PIN;

Arduino/McLighting/request_handlers.h

@@ -743,11 +743,15 @@ void webSocketEvent(uint8_t num, WStype_t type, uint8_t * payload, size_t lenght
          root["effect"] = strip->getModeName(strip->getMode());
        }
        #endif
-      char buffer[measureJson(root) + 1];
+      uint16_t msg_len = measureJson(root) + 1;
+      char buffer[msg_len];
       serializeJson(root, buffer, sizeof(buffer));
       jsonBuffer.clear();
       #if ENABLE_MQTT == 0
-      mqtt_client->publish(mqtt_ha_state_out, buffer, true);
+      //mqtt_client->publish(mqtt_ha_state_out, buffer, true);
+      mqtt_client->beginPublish(mqtt_ha_state_out, msg_len-1, true);
+      mqtt_client->write((const uint8_t*)buffer, msg_len-1);
+      mqtt_client->endPublish();
       DBG_OUTPUT_PORT.printf("MQTT: Send [%s]: %s\r\n", mqtt_ha_state_out, buffer);
       #endif
       #if ENABLE_MQTT == 1
@@ -901,7 +905,7 @@ void webSocketEvent(uint8_t num, WStype_t type, uint8_t * payload, size_t lenght
           return;
         }
         if(ha_send_data.active()) ha_send_data.detach();
-        ha_send_data.once(5, tickerSendState);
+        ha_send_data.once(DELAY_MQTT_HA_MESSAGE, tickerSendState);
       } else if (strcmp(topic, mqtt_intopic) == 0) {
     #endif
 
@@ -936,7 +940,7 @@ void webSocketEvent(uint8_t num, WStype_t type, uint8_t * payload, size_t lenght
         #if defined(ENABLE_HOMEASSISTANT)
           ha_send_data.detach();
           mqtt_client->subscribe(mqtt_ha_state_in, qossub);
-          ha_send_data.once(5, tickerSendState);
+          ha_send_data.once(DELAY_MQTT_HA_MESSAGE, tickerSendState);
           #if defined(MQTT_HOME_ASSISTANT_SUPPORT)
             const size_t bufferSize = JSON_ARRAY_SIZE(strip->getModeCount()+ 4) + JSON_OBJECT_SIZE(11) + 1500;
             DynamicJsonDocument jsonBuffer(bufferSize);

Arduino/McLighting/version.h

@@ -1 +1 @@
-#define SKETCH_VERSION "3.1.0"
+#define SKETCH_VERSION "3.1.1"

Arduino/McLighting/version_info.ino

@@ -257,4 +257,8 @@
  * Version Bump to 3.1.0
  * bugfixes
  * E1.31 is now working for multi segments
+ * 
+ * 18 April 2020
+ * Version Bump to 3.1.1
+ * bugfixes regarding issue #80
  */